BENCHLAB 2 Frame Kit User Guide

This guide covers installing BENCHLAB 2 in the Corsair FRAME 4000D/5000D, then setting up the software and the XENEON EDGE widget.

 

1. What You'll Need

BENCHLAB 2 (link)

  • BENCHLAB 2 PCBA
  • Power cables: 2× EPS, 1× ATX, 3× PCIe, 2× 12VHPWR
  • F_Panel cable (1×)
  • USB-C to internal USB cable (1×)

BENCHLAB 2 Frame Kit (link)

  • Hex standoffs: 4× 12mm, 3× 16.5mm, 1× 18mm
  • Screws: 8×
  • 180° USB-C adapter (1×)
  • ATX 24-pin 90° right-angle adapter (1×)

Corsair FRAME

 

2. Before You Begin

The BENCHLAB 2 Frame installation is straightforward, but it is a tight fit, so take your time.

You can install BENCHLAB 2 first or last in your build. This guide assumes all system components are already installed, with the power supply not yet connected to the system.

Tip: Make sure the power supply cables are easily reachable from the back of the chassis.

 

3. Installing BENCHLAB 2 in the CORSAIR Frame

Step 1: Connect and route the cables

Connect the BENCHLAB power cables, F_Panel cable and internal USB cable to the system components, then route them to the back of the case. The ATX 24-pin 90° adapter can make routing easier.

Step 2: Mount the standoffs

Clear the area around the motherboard tray, then mount the BENCHLAB 2 Frame Kit standoffs according to the diagram below.

Step 3: Connect the power-out cables

Connect the BENCHLAB power cables to the PSU_X connectors on BENCHLAB 2.

Step 4: Connect the PSU cables

Connect the PSU power cables to the SYS_X connectors on BENCHLAB 2.

Step 5: Connect the F_Panel cable

Connect the F_Panel cable to the BENCHLAB 2 FP_SYS1 connector. You can also connect the case's F_Panel to the FP_CASE1 connector.

Step 6: Attach the USB-C adapter

Connect the 180° USB Type-C adapter to BENCHLAB 2.

Step 7: Mount the board

Carefully place BENCHLAB 2 on top of the standoffs and fasten it with the screws. Note: This may be a tight fit, so go slowly.

Step 8: Connect the internal USB cable

Connect the internal USB cable to the BENCHLAB 2 180° USB Type-C adapter. Note: You may need to hold the adapter in place to ensure a secure connection at both ends.

Step 9: Power-on test

Turn on the PSU without turning on the system. If BENCHLAB 2 is installed correctly and the RGB switch is set to Play mode, the RGB lighting should light up.

 

4. XENEON EDGE Widget Setup

If you also own a XENEON EDGE, we've developed an iCUE widget for BENCHLAB. You can find it on our Downloads page.

 

Quick installation steps

Step 1: Download the BENCHLAB iCue Widget & BENCHLAB Dashboard from our Downloads page.

Step 2: Install the BENCHLAB Dashboard software. This will also install the BENCHLAB Service which the iCue widget connects to.

Step 3: Launch iCUE on your PC and make sure your CORSAIR device is connected and recognized. Go to the Widgets section and click the + icon to open the Import Widget dialog. Drag your .icuewidget file into the Import Widget dialog, or click to browse and select it from your computer. Once the file is selected, click the confirm/import button to install the widget.

Step 4: Once installed, the widget appears in your iCUE widget library. From there you can add it to your device screen and customize its settings. We recommend:

  • Size: XL
  • Data Source: BENCHLAB Service
  • Service Transport: Auto
  • Custom Style: Enabled